ACDelco 15-80571 Blower Motor Resistor Assembly Reviews

If your addict loses a couple speeds over calculate, then this is extremely liable the culprit. Ultimately, you will drop all speeds apart early HIGH and OFF (no problem, OFF is a alacrity). This resistor quantity lives surrounded by your blower housing, liable to keep it cool as the addict runs, keep for can not get on to the grade over calculate. This earlier cycle calculate, my AC drain got plugged, and the blower housing got fill up in it and shorted made known the resistor quantity.Notification: extremely tiresome to entrance! Push the passenger seat all the road in trade. I in detail do this upside-not effective including my head on the floor and my feet headed for the roof.To replace, you be inflicted including to remove the kick panel under the glove quantity (only cut the fake push pins, replacements can be bought at any car parts store). Then disconnect the cherry/black potential early the blower motor, and the black rubber tube including the intention of runs between the motor and the housing. Then remove the addict/motor plate by removing the 3 gold torx screws and lowering the plate bitter the housing. The resistor quantity is in trade headed for the firewall, including 3 extremely small enchantment screws ground it early the underneath of the blower housing: 2 screws ground lone advantage by the firewall, and a release screw ground the contrary advantage. Remove the wiring use. To get on to the resistor quantity bitter, it is easiest to loosen only the release screw and then waggle it headed for you bitter the in trade 2 screws.Reassembly is austerely the directions in back.
- JoeyP

They must do extra investigate. The gathering skeleton fit but as I went to promote it into my fan motor the plait was too short so I had to cut the end off in cooperation new and old resistor packs and extend the new packs promote to get to the motor. They of way said it would fit. NOT.
- Dan Mercer

A quite common issue on w-body vehicles (Monte Carlo, Impala, Grand Prix, Regal, Century, Intrigue) is the blower resistor dying, causing any complete or partial HVAC failure. Replacement of this part takes some finesse, time, preparation ahead and patience. It's located under the glove box, behind the fake cover. Initially, remove the three screws and the blower fan. You might need to wiggle it out, since thick wiring might be in your way. By far the easiest way of doing the replacement of the resistor itself, which is bolted in with 7/32 bolts, is to take out the 2 you can see, then break the resistor to remove and loosen the 3rd bolt. Bolt the new one up only tightening the two you can get to.
- Adrian Stec

Not an straightforward part to exchange, save pro the extra part facility great and was the cheapest fee. Took 3 income longer than estimated arrival appointment to get on to here, save pro not excessively exalted of a take care of business.
- The Wizz

I have a 2002 Chevy Monte Carlo LS. For about 6 being I've been income with most of the fan speed settings just not effective. Once I got down to only 3 and 4 effective I looked into the fix. I was about to hold an entire new power gathering when I found out that this was the part I needed. I just installed it earlier now and all of my fan settings work! Just be forewarned... this is a part that is a pain in the butt to get out and put back in. I would urge being paid a fake closure remover for about $10 to take out the stupid fasteners on most modern cars. I used Lisle 35260 Fake Closure Remover and it worked well. Splendid manufactured goods and fast shipping, what more could you ask for?
- joem86 "Joe"

The fee on this part was great....in this vicinity semi of what I would be inflicted including compensated locally, and it was a genuine AC Delco substitution part. If your ac/radiator addict release facility on high, this is the part you call for. Added a tome to the diplomacy, and it shuipped emancipated and was expected in a hardly any income. Couldn't request for extra.
- N. Goldwater

This was the section with the intention of was looked-for in our car. It was inexpensive and easy to bed in. Took in this area an hour and with the intention of is since the old section just fell apart tiresome to get it out.
- Elizabeth Callison "Elizabeth VA"

The blower motor works fine. I've had no harms with it and saved a least $100 had my mechanic installed it. A word of notification, it's a "B...." to install physically. A buddy with genteel tools installed mine. It took an hour.
- fullwoofymoon

I did my research for my Grand Prix on my a/c radiator blower motor. The only speed on the batter for the fan with the intention of was working was the peak setting. I eventually found out thru the internet with the intention of it was the Blower Motor Resistor. (Never even knew one existed.) Thru Yahoo i was able to locate one and at the cheapest fee around. Be grateful you Yahoo! MR
- Michael J. Roche "Rochey50"

It replaces the old one just fine. Just be aware that this is not a very easy part to replace. In this case, Pontiac didn't make allocate very good access. It helps if the person replacing it is not very tall or large.
- Rollie D. Newton "R. Newton"

ACDelco 15-80571 Blower Motor Resistor Assembly

Blower Motor Resistor